Change the numbers. We print the shape.

Vases, pendant shades and planters made from four numbers. Set them, turn the piece round, and order it printed.

A white vase with twisted flutes, printed in one piece

Drag to turn it. The plate is 300 mm across.

Design

Full in the body, narrow at the neck.

Flutes
Twist
Colour Chalk
Size
150 × 240 mm
Holds
2.24 l
Weight
197 g
Layers
1,200

Three designs, one maker

The same four numbers make all three. What changes is the curve from the foot to the rim.

DesignIts curveHeight, mmWidth, mm
Full in the body, narrow at the neck.120–36080–220
Wide at the rim, narrowing to the cord.140–320160–280
Straight and wide, with a drainage hole.80–260100–280
A 3D printer half way through an orange fluted vase
A fluted vase, half printed.

From numbers to a print

  1. You set the numbers

    Height, width, flutes and twist, within the range each design prints well in.

  2. The model is made from them

    A new model for your numbers, not a stretched copy: the wall stays 1.6 mm whatever the size.

  3. Sliced into layers

    0.2 mm each, so a 240 mm vase is 1,200 of them.

  4. Printed in one line

    The wall goes up as one continuous spiral, without a seam down the side.

  5. Checked and packed

    Every piece is looked over, cleaned of strings and packed in paper.

Five colours of PLA

A plant-based plastic with a soft matt sheen, printed through and through: a scratch shows the same colour.

  • Chalk
  • Terracotta
  • Sage
  • Ochre
  • Ink

Walls 1.6 mm, layers 0.2 mm. Wipe clean with a damp cloth; not for the dishwasher.

A coil of white filament, a kilogram of it, tied with wire
A kilogram of filament, coiled for the printer.
Printed models on a table: a red lattice ball, a cube with a coin inside, a green star
Not every shape is a vase.

Or bring your own model

Anything the configurator does not make: upload the file and it is quoted as it is.

  • .stl
  • .step
  • .stp
  • .iges
  • .igs
  • .dxf
  • .dwg
  • .svg
  • .pdf

Up to 50 MB a file. Drawings are fine too, with the sizes marked.

Upload a model

Before you order

Can the vase hold water?

A printed wall can weep a little along its layers. For fresh flowers, stand a glass or jar inside, or ask for the inside sealed.

Which bulb goes in the shade?

LED only. PLA softens at about 60 °C, which a filament or halogen bulb can reach; an LED bulb stays well below it.

Can the planter go outside?

PLA is best indoors. For a planter that lives outside, ask for PETG, which stands sun and frost better.

Can I change something the configurator does not?

Upload your own model, or a drawing with what you want changed, and we quote it as it is.

Why are the sizes limited?

Each design has the range it prints well in, inside the printer's 300 × 300 × 400 mm. Outside it, the wall sags or the twist tears.

Your numbers. Our printer.

Configure and order

Pictures from Wikimedia Commons: 3D Printed Vase, D Eaketts, CC BY-SA 4.0; 3D printed vase, Sumanbargavr, CC BY-SA 4.0; 3D printed bowl, Sumanbargavr, CC BY-SA 4.0; Prusa i3, RepRap 3D printer printing, John Abella, CC BY 2.0; 1 kg refill filament, Suit, CC BY-SA 4.0; 3D Printing and Mathematics models, US Embassy South Africa, public domain.